A Survey of Inverse Surface Design From Light Transport Behavior Specification

Inverse surface design problems from light transport behavior specification usually represent extremely complex and costly processes, but their importance is well known. In particular, they are very interesting for lighting and luminaire design, in which it is usually difficult to test design decisions on a physical model in order to avoid costly mistakes. In this survey, we present the main ideas behind these kinds of problems, characterize them, and summarize existing work in the area, revealing problems that remain open and possible areas of further research.     

热力学相图计算技术在闪速燃烧合成氮化硅铁中的应用

将热力学相图计算技术应用于Si-Fe-O-N体系,以评估由FeSi75粉闪速燃烧合成氮化硅铁的条件和目标产物。结果表明:将闪速燃烧温度控制在1200～1500℃之间较为适宜,此时平衡态产物中除主要含有Si3N4以外,还有一定量的Fe与Si间化合物和少量稳定的SiO2存在。此计算结果与实际试验结果吻合良好。     

由碳五馏分合成甲基叔戊基醚工艺的研究

以催化裂化C_5馏分与工业甲醇为原料,D005型大孔强酸型阳离子交换树脂为催化剂,采用筒式膨胀床双反应器,考察了甲基叔戊基醚的合成工艺条件。一阶反应器的操作条件为：循环比为2：1,醇烯比为1.2：1,入口温度为70℃,空速为6 h~(-1),平均转化率为53.63%；二阶反应器的操作条件为：入口温度为50℃,空速为1.2h~(-1),平均转化率为71.32%,全调合方案可以使催化裂化汽油的辛烷值平均提高0.55个单位。     

焦化干气一步法预处理多功能催化剂的工业侧线试验

对焦化干气一步法预处理工艺催化剂进行了工业侧线试验。考察了温度和体积空速对催化剂的活性及催化剂稳定性和加氢选择性的影响。催化剂为以复合型ZnO和过渡金属氧化物为活性组分的多功能催化剂,用于低温下焦化干气中烯烃加氢和硫化物脱除。试验结果表明,在压力1.6MPa、温度285～350℃、空速100～500h-1的条件下,多功能催化剂能将焦化干气中烯烃的体积分数由8%～14%降至0,总硫含量从10～70μg/g脱除至5μg/g以下;经28d考核,多功能催化剂仍保持良好的烯烃加氢和硫化物脱除性能,可用于精制焦化干气。     

现场总线控制系统中GPS精确校时的实现

针对现场总线控制系统精确校时和时间统一的要求,提出了3种利用GPS授时功能对总线式系统进行校时的方案.以GPSDEC授时型接收机为例,其校时可通过RS-232接口端ASCII码信息和DCF77信号、及输出端自定义脉冲信号实现.开放性要求高的大中型总线网络及通用的智能设备,当总线系统中的通讯协议具有时钟功能时,可采用广播式校时法对设备逐个校时.顺序式校时主要针对下层智能设备种类较多的大型总线系统内的前置通讯,并按通讯机的先后依次校时.对时间精度要求较高且下层智能仪表具有时钟同步信号接口的小型总线系统,宜采用单点式校时.     

A geometry-based error estimation for cross-ratios

For choosing specific cross-ratios as 2D projective coordinates in various computer vision applications, a reasonable error analysis model is usually required. This investigation adopts the assumption of normal distribution for positioning errors of point features in an image to formulate the error variances of cross-ratios. Based on a geometry-based error analysis, a straightforward way of identifying the cross-ratios with minimum error variances is proposed. Simulation results show that the proposed approach, as well as a further simplified alternative, yield much better estimations of minimum error variances in terms of accuracy, cost, and stability compared with some other methods, e.g., the one based on the rule given by Georis et al. (IEEE Trans. Pattern Anal. Mach. Intell. 20 (4) (1998) 366). Some causes of the performance differences in the estimations are explained using a special configuration of point features.     

国电双鸭山发电有限公司工业废水的回收

阐述了国电双鸭山发电有限公司工业废水回收的必要性和废水排放现状.确定实现污水零排放工程的方案.计算了回收改造工程实施后的经济效益,这对保护电厂周边环境、减少环境污染有重要意义.     

工业厂房48M抽柱工程施工工艺

以莱钢万力H型钢有限公司抽柱换梁工程为例，介绍行车梁拼装、柱加固拆除及托粱吊装前后的测量观测。     

铜杆信息采集系统的研究

阐述了铜杆生产过程中信息采集系统的主要研究内容；概括了硬件的结构和选用的主要设备；阐述了上位机软件的主要模块及实现方法；系统采用面向对象的编程方法，界面友好，操作简单，功能完善；实际运行效果良好，具有较好的应用前景。     

Determining stress intensity factors of composites using crack opening displacement

The main purpose of this paper is to find the mixed-mode stress intensity factors of composite materials using the crack opening displacement (COD). First, a series solution of the composite material with a crack was used to evaluate COD values. Then, the least-squares method was used to calculate mixed-mode stress intensity factors. This algorithm can be applied to any method that generates or measures COD values. The major advantage of this method is that COD values very near the crack tip are not necessary. Both finite element simulations and laboratory experiments were applied to validate this least-squares method with acceptable accuracy if the even terms of the series solution are removed.